1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
|
/* -*- Mode: C++; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*- */
/*
* This file is part of the LibreOffice project.
*
* This Source Code Form is subject to the terms of the Mozilla Public
* License, v. 2.0. If a copy of the MPL was not distributed with this
* file, You can obtain one at http://mozilla.org/MPL/2.0/.
*
* This file incorporates work covered by the following license notice:
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed
* with this work for additional information regarding copyright
* ownership. The ASF licenses this file to you under the Apache
* License, Version 2.0 (the "License"); you may not use this file
* except in compliance with the License. You may obtain a copy of
* the License at http://www.apache.org/licenses/LICENSE-2.0 .
*/
#ifndef INCLUDED_VCL_INC_UNITS_HRC
#define INCLUDED_VCL_INC_UNITS_HRC
#define NC_(Context, String) reinterpret_cast<char const *>(Context "\004" u8##String)
std::pair<const char*, FieldUnit> SV_FUNIT_STRINGS[] =
{
// To translators: This is the first entry of a sequence of measurement unit names
{ NC_("SV_FUNIT_STRINGS", "mm"), FieldUnit::MM },
{ NC_("SV_FUNIT_STRINGS", "cm"), FieldUnit::CM },
{ NC_("SV_FUNIT_STRINGS", "m"), FieldUnit::M },
{ NC_("SV_FUNIT_STRINGS", "km"), FieldUnit::KM },
{ NC_("SV_FUNIT_STRINGS", "twips"), FieldUnit::TWIP },
{ NC_("SV_FUNIT_STRINGS", "twip"), FieldUnit::TWIP },
{ NC_("SV_FUNIT_STRINGS", "pt"), FieldUnit::POINT },
{ NC_("SV_FUNIT_STRINGS", "pc"), FieldUnit::PICA },
/* To translators: double prime symbol for inch */
{ NC_("SV_FUNIT_STRINGS", "″"), FieldUnit::INCH },
{ NC_("SV_FUNIT_STRINGS", "\""), FieldUnit::INCH },
{ NC_("SV_FUNIT_STRINGS", "in"), FieldUnit::INCH },
{ NC_("SV_FUNIT_STRINGS", "inch"), FieldUnit::INCH },
/* To translators: prime symbol for foot */
{ NC_("SV_FUNIT_STRINGS", "′"), FieldUnit::FOOT },
{ NC_("SV_FUNIT_STRINGS", "'"), FieldUnit::FOOT },
{ NC_("SV_FUNIT_STRINGS", "ft"), FieldUnit::FOOT },
{ NC_("SV_FUNIT_STRINGS", "foot"), FieldUnit::FOOT },
{ NC_("SV_FUNIT_STRINGS", "feet"), FieldUnit::FOOT },
{ NC_("SV_FUNIT_STRINGS", "miles"), FieldUnit::MILE },
{ NC_("SV_FUNIT_STRINGS", "mile"), FieldUnit::MILE },
{ NC_("SV_FUNIT_STRINGS", "ch"), FieldUnit::CHAR },
{ NC_("SV_FUNIT_STRINGS", "line"), FieldUnit::LINE },
{ NC_("SV_FUNIT_STRINGS", "pixels"), FieldUnit::PIXEL },
{ NC_("SV_FUNIT_STRINGS", "pixel"), FieldUnit::PIXEL },
/* To translators: degree */
{ NC_("SV_FUNIT_STRINGS", "°"), FieldUnit::DEGREE },
{ NC_("SV_FUNIT_STRINGS", "sec"), FieldUnit::SECOND },
// To translators: This is the last entry of the sequence of measurement unit names
{ NC_("SV_FUNIT_STRINGS", "ms"), FieldUnit::MILLISECOND }
};
#endif // INCLUDED_VCL_INC_UNITS_HRC
/* vim:set shiftwidth=4 softtabstop=4 expandtab: */
|
